Construction industry GW50 Manual Bending Machine

When it comes to the construction industry, we will think of reinforced concrete, indeed, do the building is very hard, very hard these bars, you are not also want to know how steel is bent it? Yongyi Tongfeng come today to tell you the answer. That is,GW50 Manual Bending Machine, which is a machine designed for the construction industry, with it, the accuracy, the efficiency of our work has been greatly improved.
But we must now also do not know the machine it, but from its literally, this machine is designed for bending rebar, indeed, we all can understand. Next, I will for everyone to do a brief introduction. GW50A Automatic Bending Machine is the most common gear type, such steel bending machine operation is very simple to use, the internal structure is very clear, so we usually use this machine.
Then the automatico bending machine specifically how does it work? When we use such a machine can bend steel degree, modeling, and so an adjustment can be done, it can be very precise adjustment of these numbers, so the life of GW50 Manual Bending Machine will be more long-term. Therefore, when we use these machines will be very convenient, but the accuracy of the work is very high.

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: GW50A Automatic Bending Machine features described...

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: GW50A Automatic Bending Machine features described...: GW50A Automatic Bending Machine  is composed of motor, reducer, working turntable, is scheduled board, recliners internal teeth constitute...

GW50A Automatic Bending Machine features described turbine gear

GW50A Automatic Bending Machine is composed of motor, reducer, working turntable, is scheduled board, recliners internal teeth constituted, its main features are: the inner tooth recliner in touch blocks and are fixed to the angle of the handle and the tone correspondence with the lower end of the limit switch for the upper rotation axis and tune the control angle of the handle is fixed to the inner tooth gear and tune sheet and the angle of the handle on the relative engagement.
   Turbo reducer steel bending machine fixed structure relates to novel metal machining fixed structure, especially the main body fixed by the ears and the fixed cover two components, fixed at the top of ear design reducer body side, and deceleration setting a fixed cover flange can make gear from bottom set into bending machines, machine preset holes and locking, can make use of new gear reducer is stable, to avoid the occurrence of jitter reducer, extend the life of the bending machine, disassembly is more convenient, and improve work efficiency, and therefore has a strong practical.
    Turbine reducerGW50 Manual Bending Machine fixed structure, which is made up of body and fixed cover fixed ears, whose main feature is the side reducer body is provided with a fixed ear and fixed cover design into a flange shape, fixed cover in gear after locking the machine by the audience set into the machine direction preset fixed cover hole corresponding to the ear by a bolt lock into fixed and fixed to the machine.
    These are the introduction of steel bending machine turbo gear fixed structure, by the above complaints about I think everyone on the bending machine turbine gear have a certain understanding, which can help you be more clear understanding of the steel turbine reducer feature, we are in the process of steel processing in the better use of GW50A Automatic Bending Machine.

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: Correct operation of GW50 Manual Bending Machine s...

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: Correct operation of GW50 Manual Bending Machine s...:     If everyone comes to   GW50 Manual Bending Machine , I think there may be some people still heard, although not closely linked with peo...

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: Correct operation of GW50A Máquina Doblado automát...

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: Correct operation of GW50A Máquina Doblado automát...:     If everyone comes to GW50A Máquina Doblado automático , I think there may be some people still heard, although not closely linked with...

Correct operation of GW50 Manual Bending Machine should pay attention to the details of what matters

    If everyone comes to GW50 Manual Bending Machine, I think there may be some people still heard, although not closely linked with people's lives, but its scope is very broad. The use of such a large device will certainly there is a certain degree of risk, so how to properly use, operation of the device is worth every staff learning, and today we take a look, hope can help staff correctly.
Before first use, do not worry turn on the power to enter use, you should first check the mechanical performance is not good, bench and table bending machines must maintain a level of state, and we must do a variety of mandrel tool block. Installation should be in accordance with the mandrel diameter and bending rebar processing machine to match, and the mandrel diameter should be 2.5 times the bar diameter.
    Secondly, we must check the mandrel, the stopper, the turntable so the details are not places where there is damage, such as cracks, shield is not fastened, if you find any problems with the details, to adjust to solve the problem immediately. Empty after running for a while, if confirmed to be functioning normally, and then enter into formal operation.
    Thirdly, the formal entry into the job, should be inserted in a steel turntable fixed with a gap inside the other end should be close to the body fixed and pressed his hand tightly, to ensure the body is fixed.
    Then, in the device operation,GW50 Manual Bending Machine is not able to replace the spindle, change the angle, but also remember not to refuel or clear, these should be good to check before the device is running, avoid experiencing more trouble.
    In addition, equipment operation, is strictly prohibited within the operating radius of GW50A Máquina Doblado automático and the body does not have a fixed side stop people, to avoid damage to the surrounding people.
    Finally, after the job is completed, to clean up the site, maintenance equipment, especially important to de-energized.
    More to tell you is about how to properly operate GW50 Manual Bending Machine, these are very important, and many of them are reflected in the details of the place, in fact, details are very important, and often is a detail of the problem could lead to more big problem. So, I hope the above considerations employees can pay attention to it, the safe operation of equipment that is the most important.

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: Buy GW50A Automatic Bending Machine need to know ...

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: Buy GW50A Automatic Bending Machine need to know ...: First, choose well-known, large-scale manufacturers. Manufacturers need to carefully choose, now often promote how their manufacturers how ...

Buy GW50A Automatic Bending Machine need to know three important details

First, choose well-known, large-scale manufacturers. Manufacturers need to carefully choose, now often promote how their manufacturers how well the network, but this is only one-sided on the network, to really buy it,GW50A  Automatic Bending Machine should personally lead manufacturers to take a look, understand the manufacturer's production capacity, environment , as well as the level of quality of service and staff personnel, summary judgment by the manufacturers of these indirect authenticity.

Second, remember not to forget the service. Many customers after the purchase of equipment, there is always a problem in the device will be remembered after sales service, but this time to think of it is probably too late. Such large-scale equipment GW50A  Automatic Bending Machine be sure to consult the manufacturer service and things that inevitably occur in the use of small problems, if they have these little problems, I am afraid will be very troublesome. But if you have a service that you can reduce a lot of trouble, they will help you solve the problem.

Third, check the quality of the equipment on the spot. GW50A  Automatic Bending Machine  needs to check the quality of the spot, it is best to let the staff help operate it, in the course of device operation, if a problem is found, must be promptly replaced or returned. The most important thing is to check the various parts of the device parts, to see which parts manufacturer out. If the device is damaged after a part, it is best to replace the same parts manufacturers to ensure the normal operation of the device.

Over to you about the three basic things about buying GW50A  Automatic Bending Machine needs attention. Steel bending machine such large equipment cost a lot of money, any one industry will not easily funded, certainly in many aspects of the investigation after the final determination of an ideal device, in particular, should choose the time and attention to detail issues.

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: GW50A Automatic Bending Machine operating specifi...

GW50A Automatic Bending Machine，GW42D Automatic Bending Machine，GW42E Automatic Bending Machine: GW50A Automatic Bending Machine operating specifi...:  1, Placed GW50A  Automatic Bending Machine , should choose a more smooth, solid, broad place before and after symmetrical triangular wooden...

GW50A Automatic Bending Machine operating specifications

 1, Placed GW50A  Automatic Bending Machine , should choose a more smooth, solid, broad place before and after symmetrical triangular wooden wedge.

 2. Do not place the power cable to GW50A  Automatic Bending Machine 's buttons, you should have received an additional control power switch. The motor should be grounded, ministries wire, electrical equipment should be well insulated.

 3, The operation is prohibited other personnel into the operating area, running the motor, hydraulic pumps and other transmission parts found abnormal noise should stop after cutting the power for maintenance. Operation prohibit cleaning, lubrication.

 4, We must add a little oil before use. Not use less than blocked shaft GW50A  Automatic Bending Machine  diameter bend, bend steel must first straightening work shall not be bent.

 5, After work, turn off the power, mechanical cleaning and maintenance work. If outside, before leaving after the power switch box should be locked.

 6, Should pay attention to before starting the position and direction of bending steel protruded prevent open the wrong wounding.


 7, The work should be checked before each transmission parts fastening bolt through the rear idle test confirmed safe before doing any work.

 8. Replace the bent pin and a fixed pin midnight on the turntable, GW50A  Automatic Bending Machine  should cut off the power to stop the rotation after.